Steel truck wheels. Sized to your hub.

Tubeless 17.5–24.5 in and tube-type 20 in steel wheels for trucks, trailers, buses and OTR machines.

See wheel sizes
Columns of silver-grey 22.5 inch tubeless steel truck wheels stacked along the finishing bay, with painted wheels hanging on the coating line beyond
Finished wheel bay / Shandong, China
Wheel index / Six families

Every common size.
One bolt-pattern check.

Six size families on ISO, hub-piloted and JIS bolt patterns.

All wheel sizes →OTR rims →
Specification / At a glance

Full offset and load tables are on each size page.

  • 01Rim diameter17.5–24.5 inTubeless truck, trailer and bus wheels; tube-type at 20 in.Size range →
  • 02Bolt pattern10 × 335 mmISO 4107 with M22 studs. Hub-piloted 10 × 285.75 mm and JIS 8 × 275 mm too.Bolt patterns →
  • 03Fatigue testSAE J267Radial and cornering fatigue per size, also run to ISO 3894.Fatigue test method →
  • 04FinishE-coatCathodic e-coat primer under a powder top coat, colour to RAL.Finishes →
01 / About Rimward

A steel wheel maker in Shandong.

We roll rims, press discs and finish complete steel wheels for trucks, trailers, buses and OTR machines.

About Rimward →

Rimward Wheel Co., Ltd.

Sells to wheel and tyre wholesalers, trailer builders and fleet buyers.

Shandong, China
02 / Wheel line

Coil in.
Painted wheel out.

Rims are rolled and flash-butt welded, discs pressed and punched, then joined and coated on one line.

Flash-butt welder closing a rolled steel rim hoop, with roll-forming machines and racks of rims behind

Rim rolling / Flash-butt welding / Disc pressing / E-coat and powder

See the wheel line →Book a video tour
Built around the axle

Three axles.
Three wheel families.

Rim width and offset are set by the axle and tyre you run.

Wheels by vehicle →
  • Dual steel wheels on the drive axle of a truck tractor at a logistics yard01

    Trucks and tractors

    Steer and drive axles; duals on 4×2 and 6×4 tractors.

    22.5 × 8.25 / 22.5 × 9.00
  • Wide-base single steel wheels on a tri-axle semi-trailer in a container yard02

    Semi-trailers

    Wide-base singles in place of duals on tri-axle trailers.

    22.5 × 11.75 / 22.5 × 14.00
  • Multi-piece OTR steel rim with lock ring on a wheel loader in a quarry03

    Loaders and dump trucks

    Multi-piece rims with lock ring for earthmover tyres.

    25 in 3-piece / 5-piece
From size check to container

Four steps to a loaded container.

  1. 01

    Confirm

    Size, bolt pattern, offset and load rating checked against your axle.

    Output / Signed spec sheet
  2. 02

    Sample

    One sample wheel per size, with fatigue and run-out results.

    Output / Sample and test report
  3. 03

    Produce

    Rolled, welded and coated in lots; run-out and air-tightness per lot.

    Output / Lot inspection record
  4. 04

    Load

    Wheels stacked and strapped into 20 ft or 40 ft HQ containers.

    Output / Packing list and photos
Tested before it ships

Test the wheel.
Ship the lot.

Each size is fatigue-tested to SAE J267 and ISO 3894 before the first lot ships.

Bolt holes and centre bore are gauged to ISO 4107 on every lot.

Test methods and certificates →
Test plan

Four checks per size.

Radial fatigue, cornering fatigue, run-out and air-tightness.

SAE J267 / ISO 3894 / ISO 4107
Three steel truck wheels painted silver, white and black, with a caliper and bolt-circle gauge on the workbench
03 / OEM and private label

Your offset.
Your colour.

Send an axle drawing or a sample wheel; we match it, paint it and stamp your mark.

Offset (ET) · Centre bore · Valve hole · RAL colour · Private stamp

Send your axle drawingOEM and private label →
Your next container

Send the size.
Get a quote.

Tell us the size, bolt pattern and quantity; we reply with price and packing.

Used only to answer this enquiry. Privacy policy